C.A. Technologies 22-1046 Series 200H HVLP Air Cap

Equip your C.A. Technologies Lynx 200H pressure-feed spray gun with the genuine 22-1046 HVLP air cap. Designed for corrosion-control finishing, this Series 200H air cap supports dependable atomization of enamels, urethanes, waterborne topcoats, and other industrial coatings.

Match the air cap to the gun, fluid nozzle, and coating so you can produce a clean pattern without fighting the finish.

Performance Highlights

• Designed for the C.A. Technologies Lynx 200H HVLP spray gun
• Built for pressure-feed corrosion-control applications
• Air consumption of approximately 22 CFM
• Rated at 22.5 CFM at 47 PSI maximum listed inlet pressure
• Configured for use with a 1.4 mm fluid tip for the listed materials
• Genuine C.A. Technologies Series 200H air cap

HVLP Atomization for Corrosion-Control Finishing

The air cap directs compressed air around the coating as it leaves the fluid nozzle. Its precision air passages and horn openings control atomization, pattern shape, and fan development.

The C.A. Technologies 22-1046 air cap is engineered for the Series 200H HVLP platform. When matched with the correct fluid nozzle and needle, it helps the Lynx 200H produce a controlled spray pattern for industrial topcoats and corrosion-control materials.

Features

• Series 200H HVLP air cap
• Made for pressure-feed spray applications
• Compatible with the Lynx 200H corrosion-control gun
• Supports a 1.4 mm fluid-tip configuration
• Approximately 22 CFM air consumption
• Supports an approximately 11-inch maximum pattern under proper conditions
• C.A. Technologies part number 22-1046

Benefits

• Improve atomization: Correct airflow helps break the coating into a controlled and uniform spray.
• Maintain pattern consistency: Proper horn air supports an even fan from top to bottom.
• Support transfer efficiency: Correct HVLP setup helps place more coating on the part with less uncontrolled overspray.
• Handle industrial topcoats: The listed 1.4 mm configuration works with many enamels, urethanes, and waterborne finishes.
• Restore gun performance: Replacing a worn or damaged air cap can correct pattern problems that cleaning alone cannot solve.

Compatible Spray Gun

• Gun: C.A. Technologies Lynx 200H
• Feed type: Pressure feed
• Technology: HVLP
• Application: Corrosion-control finishing

Important: Match the air cap to the spray gun model, fluid nozzle, fluid needle, coating viscosity, and desired pattern. Similar C.A. Technologies air caps may fit the retaining ring but provide different airflow and atomization characteristics.

Required Fluid-Nozzle Series

The 22-1046 air cap must be used with a compatible C.A. Technologies 32-02XX fluid nozzle. Confirm the complete fluid-nozzle and needle combination before ordering or installing the air cap.

• Listed fluid-tip size: 1.4 mm
• Required nozzle family: 32-02XX

Typical Coating Materials

• Industrial enamels
• Urethane coatings
• Waterborne topcoats
• Medium-viscosity primers
• Protective industrial coatings
• Corrosion-control finishes

Air Requirements

• Nominal air consumption: Approximately 22 CFM
• Published airflow: 22.5 CFM at 47 PSI
• Maximum listed inlet pressure: 47 PSI

The compressor and air-delivery system must supply the required airflow at the spray gun. A compressor can display adequate static pressure while failing to deliver enough CFM through undersized hose, restrictive fittings, dirty filters, or inadequate piping.

Set atomizing pressure with the gun triggered and air flowing. Begin at the lowest pressure that produces acceptable atomization, then make controlled adjustments to air pressure, fluid pressure, and fan width.

Signs an Air Cap Needs Attention

Inspect the air cap when the spray pattern becomes heavy on one side, split, distorted, inconsistent, or difficult to adjust. Dried coating inside the horn openings or center air passages can create many of the same symptoms as a damaged cap.

Clean blocked passages with the recommended solvent and a nonmetallic air-cap cleaning tool. Never use drill bits, wire, or other hard metal objects that can enlarge or deform the precision openings.

Installation and Setup

Completely relieve air and fluid pressure before removing the existing air cap. Inspect the fluid nozzle, retaining ring, air-cap seating surfaces, and cap openings for coating buildup, wear, or damage.

Install the 22-1046 squarely over the compatible 32-02XX fluid nozzle. Tighten the retaining ring only enough to hold the cap securely while still allowing pattern orientation.

After installation, test the spray pattern and adjust atomizing air, fluid pressure, and fan control for the coating being sprayed.

Quick Specifications

• Manufacturer: C.A. Technologies
• Product type: HVLP air cap
• Part number: 22-1046
• Series: 200H
• Compatible gun: Lynx 200H
• Feed configuration: Pressure feed
• Listed fluid-tip size: 1.4 mm
• Required nozzle series: 32-02XX
• Air consumption: 22.5 CFM at 47 PSI
• Maximum pattern width: Approximately 11 inches
• Application: Corrosion-control finishing

Put the Correct Air Cap on the Job

Good finish quality starts with a matched atomizing system. The 22-1046 air cap, compatible 32-02XX fluid nozzle, proper air supply, and correct fluid pressure work together to produce a stable pattern and repeatable coating results.

Order the C.A. Technologies 22-1046 Series 200H HVLP air cap today, or contact us for help confirming your Lynx 200H setup.